VINTAGETRACTORS.COM
AND
RUSTY ACRES RANCH
Rear wheel, front end, and
steering Parts for John Deere Model 40 Tractors
=
-
M3801T Special rim bolt, 9/16 x 2 1/4", not available
at this time
M374T Nut lock. Out of stock
M375T, Special rim nut, $2 each
M343T rear weight, $90, one only
available, 145 pounds, can be shipped UPS
-
Pair of M2729T rear weights, 145 lbs. each, to fit
S and U models, $90 each or $150/pair
M2650T hub clamp with no keyway, very good condition,
for MT, 40T, 420T,W, 430T,W, some 1010 rear axles, $80, one available
(T10171T) M2648T (Sub for M1793T) Rear hub for MT,
40T, 420T,W, 430T,W, some 1010 rear axles, $50 each, two available
M1793T (Sub for T10171T and M2648T) Rear hub for MT,
40T, 420T,W, 430T,W, some 1010 rear axles, $50, one available
Steering wheel 17 1/2 inch diameter, $25
Tie rods, good condition, $45 each or $80/pair
Steering box with M508T housing and AM819T (AM2574T)
vertical shaft, in good working condition, nut the bottom oil
seal and the steering pin both need replacement, $150. This is
used on 40U to serial 63119 and 40S to serial 69403: coming soon.
M2742T (T11329T) Steering arm for H, S, T, W and later
U and S with two pin steering box, $35
-
Steering box #2 for 40T to sn 77354, 40H to sn 60060
and all MT, has AM3159T housing, the pins show slight wear, may
need a new bottom seal, $150
M1593T pivot pin, show some wear, as-is, $10
-
AM1463T spindles, $45 each, your choice
Late style clamp for adjustable front axle, $15
M435T Center steering arm, $30
M1252T steering arm with a well done repair, $10
M843T upper spindle, $80
Thrust bearing only (washer not available), $15
-
M849T, steering gear support
(sub. AM946T), $25, your choice
#1 M843T Spindle with M1171T Fork and two M1180T clamps,
$110
-
#2 M843T Spindle with M1171T Fork and two M1180T clamps,
$80
M2724T steering arm, no breaks or repairs, $35
-
M849T, steering gear support
(sub. AM946T), $25, your choice
M1593T Front axle pivot pin for
early 40U, shows wear, $5
M1593T pivot pin for earlier
40U, $15
M2666T pivot pin for later 40U,
shows some wear, but usable, $15
Center steering arm, $30
#1 M2164T axle with M2402T knees, for 40U, good needle
bearings in knees, $80
M1460T axle clamp set, $15
M1387T axle clamp pin, $5
- 
AM2163T spindle for U models,$35, four available
M825T Hub cap, $12.50
- -
Front wheel hub, no breaks or repairs, includes both
good bearings and retainer seals, $32 each similar to above, several
available
-
JD3002T, Original front wheel #1, good condtion, 4
x 16, $40
-
JD3002T, Original front wheel #2, good condtion, 4
x 16, $40
-
JD3003T 5 x16 front wheel #2 that came from a 440,
$50
JD3002T, Original front wheel
11.2-24
Firestone 10-24 (11.2-24), sound condition, 20% on
bars, $25
Goodyear 11.2/10-24, sound condition, $50
12.4-24
- 
Powermark 12.4-24 Very good condition, with tube, $135
-
Goodyear 12.4-24, 70% tread, slight wetherchecking,
with tube, $60