VINTAGETRACTORS.COM
AND
RUSTY ACRES RANCH
Wheels, Front
Ends, and Steering parts for John Deere Model B
Parts for both early styled
(s.n. 60,000-201,000) and late styled B (s.n.>201,000). Click here for
other JD styled B parts.
9/16-18 lug nut for rear wheels, $1.50 each or set
of six for $7.50
1/2-20 lug nuts for front wheels, $1.50 each or set
of six for $7.50
-
-
JD1268R rim, 4 x 16, this is a stamped original in
excellent condition, $100 (CS)
-
-
B1395R Steering sector gear, $40, your choice, used
on B serial # 60000-238315
B2766R Steering sector gear, used on B serial # 238316
and up, $50
-
B2191R steering eccentric, $25
ROUND TUBE WIDE
FRONT END:
-
Complete Round Wide front end to fit late A and B with
the split pedestal, Complete including the hubs, steering arms,
tie rods, mounting plates, and all mounting bolts. Nothing is
either broken or repaired-everything is in very good condition.
Ready to go to work on your tractor.
$995 plus truck freight shipping or it can be picked
up here.
If you need the split pedestal, I also have them available
for both Models A or B.
JD7760 Lock bolt with 1" nut, $15
FOR BNH:
-
Complete front end for styled
BNH with B1491R pdestal and correct AB1336R spoked 16 inch wheel
(wheel has some welds where spokes intersect with rims). Includes
steering gear, covers, and all mounting bolts. Can ship truck
freight, $495, sale pending
FOR B Two wheel
tricycle:
-
AB3106R, B1763R Pedestal, Very
good condition, $50, your choice
-
AB3106R, B1383R pedestal, Very
good condition, $50
B105R washer (between bottom
of pedestal and spindle), $16
-
AB3133R spindle, very good condition, good dust guards,
$60
-
AB3133R Spindle, very good condition
except for dust guards, $45
B918R hub, used on tricycle B with the 15 inch wheel,
includes both bearings and felt retainer, no breaks or repairs,
$40 each

AB1032R Spindle nut, $12 each
B105R thrust washer, $9
B104R pivot plate, $12
B1766R Center plate, $15
Split pedestal:
-
Lighter style,similar to above (160 pounds total)
-
-
#1,Lighter style,this is the best of the bunch (160
pounds total)
- 
Heavier style
B2673R split pedestal, $160 without sector gear and
eccentric bushing, $220 with sector gear and eccentric bushing
There are two types of B2673R, I have both types available. The
lighter one can ship UPS, the heavier one by truck freight or
you pick up only
AB3681R Steering shaft with nut, $80
Fork to fit split pedestal and the 16 inch wheels shown
below, $60
B2681R wheel with tire, with good axle and bearings,
$95 (160 lb with tire, 135 lb without)
B2681R wheel with good axle and bearings, $95 (160
lb with tire, 135 lb without)
B2681R wheel with good axle and bearings, $90 (135
lb)
Wheel cover for B2681R wheel - free with wheel
Steering wheel and horizontal
shaft parts:
AB218R (AA380R) Steering wheel, nice condition, 16
inch diameter, $25
AB3909R, AB3910R, or AB3911R Steering shaft, $30
Steering shaft stub, good worm gear, $12
JD7396R steering shaft beaing, $10 each
B1637R, Cap for steering shaft, $12
B1393R, Top steering cover, $16
B2379R hub, 2 available, includes inner and outer bearings,
$45 each
B2719R hub, 1 available, includes inner and outer bearings,
The hubs are used with the rollomatic front end. $35
B920R hub cap, $15
B2015R hub for 15 inch wheels, 2 available, includes
inner and outer bearings, $30 each
B920R hub cap, $15, several available
-
B2711R and B2712R Knuckle with dust excluder, very
good condition, $60 each
B2716R washer, $9
B2727R cap $7
Rim #1
Rim #2,
This is a pair of very rare wheels. The rear wheels have F &
H casting # HC419C in the hubs. These are similar to F & H
HC419A hubs used on the 40 inch round spoked wheels for BWH and
BNH tractors and also the 36" round spoke wheels used on
a few BN's. However, these wheels have flat spokes (not round
spokes) riveted into the hubs. The flat spokes are welded to the
38" rims. I believe they are cut downs from steel wheels,
since they would have been riveted to the rim if they were factory
wheels for rubber tires. The tractor that these wheels came from
is a wartime styled B with a tricycle front end. Thes erial tag
was missing, but the B2013R cast iron frame indicates a 1943 or
1944 wartime tractor, serial #136662-166999. This is confirmed
by the cut down fronts with the wartime hubs also on the tractor.
I have never seen or heard of a set of these hubs with flat spokes,
but the fact that the serial tag was missing makes it difficult
to do further research on them. They would look great on a tractor
with steel rims put back on them. Unfortunately, as is more often
than the case than not with these B hubs, the ears have broken
off over the years. They are all there and fit the hubs and would
work fine for a show tractor. The rims weigh 200 pounds each and
can ship truck freight. I have more photos when they were on the
tractor if you would like to see them. They are priced at $1200
for the pair due to their rarity.
B1189R hub clamp to fit the B2277R
and B1678R hub, $25
Wheel center, outer diameter 34 1/8 inch. Use this
center and your wide rim to make a light weight wheel for your
pulling tractor, the 9 hole bolt pattern fits A3248R, B1678R,
and B2277R hubs, $80
Good 9 x 38 rear rim with usable tire to fit the 38
inch centers, $90, should pick it up here but it can ship truck
freight
A3149R cast center for 38 inch rims, $50, one available,
4 mounting studs per center
-
B2188R Rear wheel hub, 12 spline axle, fits either
A3149R or A3402R Cast centers, $60, three available
A2961R Special hardened bolt to attach hub to cast
center, with nut, $2.50 each set
- 
B2189R hub clamp, $45
Special 3/4 x 4 bolt to fit the B1961R and B2189R clamp,
$6 each
B634R rim clamp, $3 each
B1189R hub clamp, $25
B1961R hub clamp $40
Special 3/4 x 4 bolt to fit the B1961R and B2189R clamp,
$6 each
A3402R Rear wheel center for 42 inch rims, $40 each
-
Pair of rear Wilson Nutwell JD 34-35 wheel weights
to fit A3402R cast centers for 42 inch rims, Each weight is approximately
250-300 pounds, $90 for the pair
8 x 42 rim #2 to fit A3402R center, very good condition,
$100
8 x 42 rim #1 to fit A3402R center, has some pitting
and one pinhole (shown), $20 as-is but should be usable
-
AA4025R 10 x 42 rim #4,One pinhole rust through, pitting
inside rim, some straightening needed at bead, $35
B634R rim clamp, $3 each