VINTAGETRACTORS.COM
AND
RUSTY ACRES RANCH
Sheet Metal Parts
and other external parts for John Deere Model B
Parts for both early styled
(s.n. 60,000-201,000) and late styled B (s.n.>201,000).
- 
Front and rear views of angood original condition AD1606R
5 hole seat, $50, usable but may want to do a little straightening.
- 
AD1606R 7 hole seat, $25, needs center repair and some
straightening
- 
AD1606R 9 hole seat, $50, has a well done center repair
24 hole implement seat with center plate stamped JD
in raised letters, $25
B1445R Medallion #2, will need
some cleaning and straightening, $20
AB1534R B RH grille #3, no rust through or cuts, but
will need some straightening and new screens, $40
AB1534R B RH #2 grille, $15
AB1534R B RH grille #4, $50
AB3569R Gasoline hood #2 for B over 201000, $35, as-is
Hood repair part, from an AB3569R gasoline hood for
B over 201000, good muffler hole, $25
Right side B hood side, will fit all styled B hoods,
$20
- 
AB3553R tank for all B over 201000, no deep rust, inside
of tank is super clean, $360
-
- 
AB1538R tank #1, used on B 60000-95999, no rust through,
but everything needs to be cleaned up and soldered together, as-is,
$25
- 
AB1538R tank, used on B 60000-95999, small tank and
bottom of big tank look good, but top of big tank is rusted, as-is,
$45
B1441R tank clips, $4 each
- 
B1695R Slant dash with B2092R
transmission cover, no breaks or repairs.$120
B1932R dash with good A80R throttle rod, dash casting
has a crack shown at the yellow arrows. $20
End cap with gauges, that may work, nice patina,, $30
B2527R End Cap #1 for B over 201000, gauges are as-is,
$25
B2527R End Cap #1 for B over 201000, $25
B2527R End Cap #2 for B over 201000, gauges are as-is,
$25
B2527R End Cap #3 for B over 201000, gauges are as-is,
$25
B2527R End Cap #5 for B over 201000, gauges are as-is,
$25
B2527R End Cap #4 for B over 201000, gauges are as-is,
$25
B2527R End Cap #6 for B over 201000, $20
B1880R transmission cover with
mount for dash and pto lever, $25
B2530R Heat shield for under tank, B over 201000, $25,
your choice
Dent free gas cap, either plain or with "Buy clean
fuel, keep it clean" $8
Shorter is AB2747R, $8
Longer is AB2746R, $8
AB3555R tank support B over sn 201000 , $10
AB2749R tank support for B under sn 201000. $10
AB2805R Three way fuel valve, rotates freely, may need
new gasket, $45
AB2805R Three way fuel valve, rotates freely, may need
new gasket, $45
AB3571R Fuel line for gasoline B 201000 and up, $18
B1766R Center plate, $15
- 
AB4247R Good frame #1 for late styled B. This frame
has no breaks or repairs, in good condition, $100 (125 lb, 54-16-15),
can ship UPS
AB4247R Good frame #2 late styled B. This frame has
no breaks or repairs, in good condition, $100 (125 lb, 54-16-15),
can ship UPS
Front end support for wartime
B, cast irn, used on #136662-166999, casting # B2013R (parts catalog
says B2012R), this was from a BW, $100
AB1509R Front frame for earlier styled B, $40, your
choice. This one has the mounting for the BW axle pivot bracket.
AB1565R tool box for B under 201000, $15
AB3538R Tool box B 201000-264778, $20, your choice
AB3994R Tool box B 264779 and up, $20
A2133R Short Shutter control rod, $25
B over 201000
B under 201000
Choke rod, $20, your choice
B1455R Throttle rod, for 60000-201000, 25 1/2"-
26" long ,$15
B1940R speed control rod, 96000-201000, 9 inch long,
$15
Speed control and carb to gov rod for B over 201000,
$15 each
C1438R spring on throttle lever shaft, new, $7
A80R throttle lever, $25
AB3574R Speed control shaft with arm. $10
Nice patina AB3579R Center cover,
all three springs are good, $35
AB3579R Center cover, primed,
all three springs are good, $30
AB3579R Center cover #2, all
three springs are good, $30
-
AB3579R center cover #3 with springs,some corrosion
inside and one spring is rusted, $10 each
AB3578R Beadblasted and primed flywheel cover, $40
AB3578R Flywheel shroud, all
are good, Your choice $30 each
Oil line to oil gauge, $8
B2286R Starter button, $15
A1892R Special Hex Nut for attaching
implements, $2 each
- 
A222R Seat channel, will need
some hole repair, $20
- 
A222R Seat channel, will need
some hole repair, $25
- 
A60R Seat channel support, no cracks, no breaks, no
repairs, $100
C1980R Pin, $8
Bolt and nut, $5
C1982R Spring holders, $5 each
A618R Seat spring, $25
8H1268R Bolt for seat spring, with 14H480R Grip nut,
$8
C1982R Cast spring holder, $5
-
A222R Seat channel, will need
some hole repair, $35
Not original equipment, but a nice seat frame that
will fit the A222R seat channel, $20
AB3930R Seat frame #1, latch is in good working condition,
$35
AB3930R Seat frame #2, latch is in good working condition,
$35
- 
AB4101R Battery box #2, no dents or cuts, corrosion
on bottom as seen in both photos, $20
- 
AB4101R Battery box #1, no dents or cuts, minimal corrosion,
back side needs some straightening, $25
Be Careful plate, $15
AB3585R Battery base #1, $15
AB299R platform , no cuts or repairs, needs a ittle
straightening, $30
AB5096R B over 201000 plake with brake latches, good
condition, $30, your choice
AB5096R B over 201000 platform
without brake latches, $20
Special bolt to attach platform
to rear axle housing, $3 each, new
Short brake latch, beadblasted
and primed, $7 each
Short brake latch, $7 each
B305R Longer 8 7/8" brake
lever, $7 each
B1388R casting # on bracket,
with an air stack that will need some work, $20
B1388R casting # on bracket,
with an air stack that will need a small amount of straightening,
$25
B2369R casting #1 on bracket,
with an air stack that does not need straightening, $50
B2369R casting # on bracket,
with an air stack that need a small anount of striaghtening at
the top air opening, $35
B2831R casting # on bracket for
latest B's with AB3641R stack, stack heeds minor straightening,
$35
B1829R ventilator pipe, $16
- 
B1604R Ventilator pipe (B60000-201000),
$20
B2832R Ventilator pipe, $16
More ventialtor tubes, $20 each
C1705R packing nut for ventilator
tubes, $5 each
AB1624R Air cleaner body for
B, slight dent(s), $25 each
AB1624R Air cleaner body for
B, no dents, $40, your choice
- 
AB4233R Air cleaner body B over 201000, no dents, $40
Air cleaner clamp with bolt and nut, $12
Air cleaner clamp without bolt and nut, $7.50
- 
AB1626R (AB3477R) Oil cup #1 or #2, No rust, no holes,
$45, your choice
AB1626R (AB3477R) Oil cup #3,No holes, no baffle, out
of round, $25
AB1626R (AB3477R) Both of these oil cups have holes,
as shown at the yellow arrows, $10 each
B2657R Ventilator inlet pipe,
$12.50
B drawbar with some modification, $20
B70R and B71R Drawbar side support
pieces, $20/pair
B72R Drawbar rear support, $25; two available, your
choice
B67R Roller pin. $5
B68R Drawbar clevis, $15
AB235R swinging drawbar, modified, $10
B2067R Drawbar tongue with B68R clevis, #$25
B3262E (B2450R) Swinging Drawbar, 42 1/2 inches long,
has a well done welded repair at the middle bend, 20
A4822R (Sub A3220R) Drawbar.43 1/4 inches long, Straight
and Not worn, $70
Drawbar hammer strap, 4 inch on center at the holes.
$15
A2510R drawbar pin, $15
AB3507R Drawbar support, $45
AB3618R Drawbar support will
fit high clearance BW and BN >201000 and BWH and BNH, serial
186134-201000, $40, your choice (40 lb)
B1798R water pipe, $25
Free radiator caps, some missing usable tangs
- 
B1869R radiator cap, good gasket and good tangs, no
dents, $19
- 
Very nice radiator cap #4, good tangs, needs gasket,
$12
B1522R step nut on shutter rod
B2523R Short shutter rod, $20
B2523R Short shutter rod, $20
- 
AB4775R Radiator shroud #1 to fit all styled B's, excellent
condition, $50 each, your choice
Screen on front frame ahead of radiator, $5
Radiator parts for B under 201,000,
B1805R upper pipe, muffler mounting
is mostly broken off, as-is, free with any order
- 
B1513R Top tank, some bolts broken
off and need to be drilled, no breaks or repairs to casting, $25
- 
B1514R bottom tank, good condition, but studs will
need to be drilled out, $20
- 
B1802R top tank #1 in good condition,
will need four studs drilled out, $35
- 
B1802R top tank #2 in good condition,
will need two studs drilled out, $35
B1802R top tank #3 in good condition,
will need two studs drilled out, $35
- 
B1803R bottom tank #2 in good
condition, $35
B1803R bottom tank #1, will need
some studs drilled and tapped, $20
B1515R sides, $12, one available
B1804R sides, $10 each
Above 201000, Radiator
parts:
Used radiator core, $25
Upper water pipe with muffler mount, B2605R, no breaks, no repairs,
$25
B2602R Top tank: No filler flange,
some bolts broken off and need to be drilled, no breaks or repairs
to casting, $25 (30 lb)
B2602R Top tank #1: Good filler
flange, some bolts broken off and need to be drilled, no breaks
or repairs to casting, $35 (30 lb)
- 
B2602R Top tank #2: Good filler
flange, some bolts broken off and need to be drilled, no breaks
or repairs to casting, $35 (30 lb)
- 
B2602R Top tank #3: Good filler
flange, some bolts broken off and need to be drilled, no breaks
or repairs to casting, $25 (30 lb)
- 
B2602R Top tank : Good filler
flange, no bolts broken off or need to be drilled, no breaks or
repairs to casting, $45 (30 lb), your choice
-
B 2603R bottom tank, no broken bolts or studs no breaks
or repairs to casting, $40
- 
B 2603R bottom tank #1, one threaded hole needs to
be drilled and tapped, $25
- 
B 2603R bottom tank #2, some thread holes need to be
drilled and tapped, $25
- 
B 2603R bottom tank #3, some thread holes need to be
drilled and tapped, $25
- 
B 2603R bottom tank, some thread holes need to be drilled
and tapped, $25, your choice
- 
B1766R Center plate, $15, your
choice
Tag and case from a BNH, #112073,
$100 (will separate)
- 
Tag and case from a 1939 B, serial
68081, no breaks or repairs, $50 or tag only $40
Tag B224747, includes serial
number research that shows this was a tricycle B sent to Modesto,
CA, $25
Tag 172868, from a BN, $35
Tag 292141. from a late high clearance BN on 42 inch
rims, $25
B tag 204268, $20
B tag 215648 from a rollomatic row crop B, $20