VINTAGETRACTORS.COM
AND
RUSTY ACRES RANCH
Parts for John
Deere Model A - Sheet Metal and External Parts
A medallion #3, split below the bottom bolt hole (yeallow
arrow in the photo, $30
Medallion #2, $15
= 
A right hand grille #1, will need some straightening,
$25
A RH grille #3, Willneed some straightening, screen
is torn, $80
Grille, RH #4, $70
A RH grille #5, $120
Grille LH #2, will need some straightening, $75
A LH grille #4, $90
A LH grille #5, $120
Battery top cover, $20
- 
Battery side covers, LH or RH, $30 each
Oil line to oil gauge, $8
Gasoline hood #1, cut at muffler hole, some surface
rust, will need some straightening, too, $100
Gasoline hood #3, cut at muffler hole, some surface
rust, will need some straightening, too, $60
Gasoline hood #5, cut at muffler hole, some surface
rust, straight, $60
End cap (dash) for A above 584000, $35
AA5554R tank #1, $45
Decent flat back gasoline tank, $30
Rounded gasoline tank, needs both cleaning and filler
neck, $10
Dent free gas cap, either plain or with "Buy clean
fuel, keep it clean" $9
Gas line from an a gasoline A above 584000, $9
- 
Two views of a new, never used three way valve, $60
Three way fuel valve for styled
A or B, good condition, will need new gasket, $40
B1901R lever for three way valve, $25
AA4828R and AA4142R Two piece Heat shield: $25
AA4827R One piece heat shield, $25
AA2254R and AA2255R Tank brackets,
$8 each, your choice
B1441R Clip for securing tank
straps to hood, $2 each
Early style drawbar, as-is, $25
Drawbar, $25
Drawbar sides (A216R and A217R) and rear support, $60
A216R and A217R drawbar side support brackets, $no
welds or repairs, $30 each
AA3843R Later style drawbar support, $45, several to
choose from
AA3848R Drawbar support (ANH, AWH below 584000 and
AN, AW above 584000), $50
- 
A drawbar support modified to fit AN, AW, ANH, AWH,
$20
- 
A3220R (A4822R) 46" long
drawbar for AA3843R and AA3848R supports, the end strap is bolted
on (not welded) and can be removed to make a correct original,
$75
AA3937R Flywheel cover #2 for
late A, $40
AA3937R Flywheel cover #1 for
late A, includes center cover, $40
- 
AB3579R center cover with springs, $30, similar to
above
A1892R Special Hex Nut for attaching
implements, $3 each
AA3987R tool box, $20
1/2" x 1" Special bolt
to attach platform to rear axle housing, $2 each, new (A above
584000)
Special washer for the platform
bolt. $1 (two available)
Brake latches, $7 each
- 
- 
AA6540R platform, A over 584000,
$35, your choice
AA6540R platform with no latches, $25
A battery box #1, Very straight,
Some corrosion rust through as shown at yellow arrows, has light
with no lens, $25
- 
A battery box #4, Very straight,
One corrosion rust through as shown at yellow arrow, $25
- 
A battery box #2, very straight,
good rails, minimal corrosion on bottom mounting that will not
be seen, $40
Be Careful plate, $9
Base for battery (fits inside
battery box), $15
- 
Seat frame #1, with seat back,
good latch parts, has been rewelded as shown, $25
Seat frame #2 with very good
latch parts and seat back, $45
Seat frame #4 with very good
latch parts and seat back, $45
Seat frame #3, without seat back,
good latch parts, $35
\